Rewording needed with extreme detail


Figure 9 and Figure 10 show the instantaneous efficiency plot against the adjusted difference in temperature. Figure 9 shows that efficiency decreases with larger temperature differences. The curve of efficiency vs time (Figure 5) and efficiency vs temperature (Figure 10) are very similar for the closed loop. So, the closed loop does not exhibit significant difference. Since the conditions under which the experiment was carried out were not perfect, the curve does not exhibit the exact shape that one would expect. If the experiment would have been carried out under ideal conditions, the efficiency line would be going down linearly. However, a linear trendline was added to the graph and it can be noticed that it does follow the path of an ideal curve. This indicates us that efficiency and (Tf, in – Tamb) are inversely proportional to each other.

On the other hand, for the open loop, the curve does not exhibit the expected shape. One of the reasons for this is that the data was gathered during a very small period so at the end very few points were used to plot the efficiency as a function of the temperature difference. However, a trendline was also added to this graph, and this trendline once again follows the same path as the curve of efficiency for an experiment carried out under ideal conditions.  

From the graph of x vs x it would be difficult to estimate the values of the heat removal factor (Fr) and the overall conductance (Uc) for the collector. The reason for this is that there are equivalent equations used to estimate these two parameters and each equation includes a variable that we were not asked to use to plot the efficiency curve. 

Equation 1 defined the collector efficiency (η) as the ratio of useful energy gain (Qu) to the incident solar energy over a period of time. Furthermore, the useful energy gain can be written in terms of certain parameters such as absorptivity (α) and transmissivity (τ) as shown in equation 5 below. 

If it is assumed that FR, τ, α and UC are constants for a given collector and flow rate, then the efficiency is a linear function of the three parameters defining the operating condition: Solar irradiance (Ic), Fluid inlet temperature (Tf, in) and Ambient air temperature (Tamb).  Then, the performance of a Flat-Plate Collector can be approximated by measuring these three parameters in experiments.

Since the efficiency curve for this specific question only asks to plot the efficiency as a function of temperature but not Ic, I cannot accurately estimate the values of Fr and Uc. I need the three parameters mentioned before to be able to approximate these values. 

However, since I have data for IC, I can make a plot of efficiency x vs x and use it to estimate the two parameters. In fact, the slope of the x vs xcurve is given by Equation 6 below.

Also, the y-intercept of the x vs x curve is related to absorptivity, transmissivity and heat removal factor by Equation 7 below.

If we assume values for x, the two relations given in Equation 6 and Equation 7 can be used to estimate values for FR and Uc.

The equation of a line indicates that mx+b

Where m is the slope and b the y-intercept.

For the efficiency curve shown below in Figure 11, we can get the equation of the line and compare it to get the value of the slope, m, and the y-intercept, b.


The respective equation of the line for the efficiency curve is given by

From this equation we see that that the slope -FR*Uc = -5.9 and y-int = 134.6.

Using Equation 7, we can plug the values assumed for x and solve for FR. From this calculation we get an estimate value of FR = 166.17. Furthermore, using Equation 6 and solving for Uc, we get and estimate value of Uc = 0.034 W/m^2 K. These estimations do not make sense because they are way off from theoretical values. The reason for this can be errors in the calculations or the fact that data is not gathered under ideal conditions. 

Another way of estimating values for Fr and Uc is to use the fact that Uc can be estimated to be 8 W/m^2 K for 1 glass cover. Hence, using this value in Equation 6 and solving for FR gives us a more accurate estimation of FR = 0.7.

Calculate your order
Pages (275 words)
Standard price: $0.00
Client Reviews
Our Guarantees
100% Confidentiality
Information about customers is confidential and never disclosed to third parties.
Original Writing
We complete all papers from scratch. You can get a plagiarism report.
Timely Delivery
No missed deadlines – 97% of assignments are completed in time.
Money Back
If you're confident that a writer didn't follow your order details, ask for a refund.

Calculate the price of your order

You will get a personal manager and a discount.
We'll send you the first draft for approval by at
Total price:
Power up Your Academic Success with the
Team of Professionals. We’ve Got Your Back.
Power up Your Study Success with Experts We’ve Got Your Back.